Essential Plumber Guide for Installing a Bathtub
Essential Plumber Guide for Installing a Bathtub
Blog Article
We've found this post involving Installing A Bathtub down the page on the net and decided it made perfect sense to talk about it with you on this page.

Installing a bathtub isn't exactly brain surgery, but it does require solid plumbing, carpentry, and also occasionally, tiling abilities. Changing an old bathtub with a brand-new one is also a moderately challenging task. If the old bathtub is easily obtainable, the project can relocate quickly; if you have to open up a wall to eliminate the old tub as well as place the brand-new tub, the task is much harder. In either situation, the task is within a residence handyman's abilities, although you will certainly need a helper to vacate the old bathtub as well as embeded in the new one. Make sure you have actually qualified on your own for the task and are comfortable trying it. As opposed to hiring a specialist to take over a halfway-completed job, it is far better to consider employing one prior to you begin. Possibilities are you might need an expert plumber to make tube links.
This post will help you set up a new tub in your restroom if you have already acquired a new bathtub as well as do not need to change the arrangement of your previous water system pipes.
Your tools and also material checklist must comprise the following:
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installation, after that the first thing you need to do is disconnect the supply of water. After doing so, activate the taps to drain pipes any kind of water remaining in the system. The procedure of removing the existing faucets can be rather bothersome because of the limited accessibility that is frequently the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a cloth ready for the staying water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been removed, utilize the same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from turning during this procedure. When the taps have been removed, the holes in the bath/basin will need to be cleaned of any old sealing compound.
Before going on to fit the new taps, compare the pipe connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet as well as the various other end supplies a connection to the existent supply pipes.
If you require to fit a monobloc, then you will certainly need reducing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, place the tap in the mounting opening in the bath/basin making sure that the washing machines are in area in between the tap and the sink. Protect the faucet in position with the manufacturer provided backnut. Once the faucet is safely in position, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with typical tap connectors. The previous type must be linked to the faucet ends first, tightening only by hand. The supply pipelines can later be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Mounting the Bath tub
Using both wood boards under its feet, place the bath tub in the called for position. The wooden boards are handy in uniformly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 small points.
The next goal is to make sure that the bathtub is leveled all round. This can be attained by checking the spirit level and also adjusting the feet on the tub till the level reads degree.
To set up faucets, fit all-time low of the outermost versatile tap adapter to the appropriate supply pipe by making a compression sign up with; then do the exact same for the other faucet.
Switch on the water system and also inspect all joints and also new pipework for leaks and tighten them if required. Load the tub as well as likewise inspect the overflow outlet and also the regular outlet for leaks.
Finally, take care of the bath paneling as explained in the producer's instruction manual. Tiling and also securing around the tub needs to wait till the tub has been used at least when as this will certainly resolve it right into its last setting.
Preparing for the Setup
Firstly, the sustaining framework provided with the bathroom must be fitted (if needed) according to the supplier's directions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is essential to ensure that if the tap includes a plastic washer, it is fitted in between the bath and the faucets. On a plastic bath, it is likewise sensible to fit a sustaining plate under the taps device to avoid strain on the bath tub.
Fit the versatile faucet adapters to the bottom of the two taps utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet through the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. See to it you utilize all of the provided washers.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom should now prepare to be suited its last setting.
Tiling Around the Bath tub
In the location where the bath satisfies the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to split an inflexible seal, creating the water to penetrate the wall surface between the bath and the tiling, causing complications with moisture as well as feasible leakages to the ceiling below.
You can pick from a selection of coloured sealers to assimilate your components as well as installations. They are sold in tubes and cartridges, and also are capable of securing gaps up to a width of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with twists of drenched paper or soft rope. Remember to always load the tub with water prior to sealing, to permit the movement experienced when the tub remains in usage. The sealer can split fairly early if you do not take into account this activity prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise conveniently available on the marketplace. It is a good idea to fit the ceramic tiles using water-resistant or water-proof glue as well as grout.
Bathtub Installation
How Important Is A Bathtub To Your Home?
High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.
Install Piping Before Tub
You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.
Position the Tub
Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.
NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.
Assemble Drain Connections
Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.
Place a Pipe For the Shower Head
First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.
Attaching Hot and Cold Water Lines
Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.
Install the Spout
Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.
NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.
Check For Leaks
Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.
estore the Bathroom Wall
Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.
https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/

I ran across that content about How to Install a Bathtub while surfing the search engines. If you liked our article if you please be sure to pass it around. Many thanks for your time. Don't forget to come visit our blog back soon.
24/7 service for plumbing emergencies. Report this page